77范文网 - 专业文章范例文档资料分享平台

汽车底盘零件焊接质量评价 - 图文(4)

来源:网络收集 时间:2019-04-22 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

SMTC 21549?2010

斜角焊缝 f2≥0.12 tmin tmin =最薄板厚 当tmin≤2时 f2≥0.2 SN≥0.7 tmin 图20 上板端面必须100%熔透 tmin -最薄板厚 多重搭接角焊缝 f3≥0.12 tmin tmin =最薄板厚 当tmin≤2时 f3≥0.2 SN1≥0.7 tmin SN2≥0.7 tmin 上板t1,t2端面必须100%熔透 tmin -最薄板厚 S≥0.7 tmin 有圆周截面的角悍缝(空心) f1≥0.12 tmin f2≥0.12 tmin tmin =最薄板厚 当tmin≤2时 f1≥0.2 f2≥0.2 tmin -最薄板厚 有圆周截面的角悍缝(实心) f1≥0.12 tmin f2≥0.12 tmin tmin =最薄板厚 当tmin≤2时 f1≥0.2 f2≥0.2 SN≥0.7 tmin 图21 tmin -最薄板厚 12

打印、拷贝即为非受控文件,请核查最新版本

- Printed Copy is Uncontrolled – Check Issue is Current -

SMTC 21549?2010

塞焊 和L×B Welded feature seam Welded seam sketch map f L≥?和 f L≥L或B f2≥0.12 tmin tmin =最薄板厚 当tmin≤2时 f2≥0.2 上板端面必图18 须100%熔透 孔必须完全封闭 Weld penetration (mm) f1≥0.12 tmin f2≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f1及f2≥0.2 f2≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f2≥0.2 Welded seam thickness (mm) SN≥0.7 tmin Profile (See Section 5.3) Figure 13 Figure 17 Figure 19 Fillet tmin -Minimum plate thickness Overlapping fillet Figure 14 Upper end Figure surface 15 should be Figure penetrated 16 100% tmin -Minimum plate thickness SN≥0.7 tmin 13

打印、拷贝即为非受控文件,请核查最新版本

- Printed Copy is Uncontrolled – Check Issue is Current -

SMTC 21549?2010

Oblique fillet f2≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f2≥0.2 SN≥0.7 tmin Figure 20 Upper end surface should be penetrated 100% tmin -Minimum plate thickness SN1≥0.7 tmin SN2≥0.7 tmin Multi-overlapping fillet f3≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f3≥0.2 Upper plate t1,t2 end surface should be penetrated 100% tmin -Minimum plate thickness S≥0.7 tmin Fillet with circumferential section (hollow) f1≥0.12 tmin f2≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f1≥0.2 f2≥0.2 tmin -Minimum plate thickness 14

打印、拷贝即为非受控文件,请核查最新版本

- Printed Copy is Uncontrolled – Check Issue is Current -

SMTC 21549?2010

Fillet with circumferential section (solid) f1≥0.12 tmin f2≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f1≥0.2 f2≥0.2 And L×B SN≥0.7 tmin Figure 21 tmin -Minimum plate thickness Slot welding f L≥? and f L≥L or B f2≥0.12 tmin tmin =Minimum plate thickness When tmin≤2 f2≥0.2 Upper end Figure surface 18 should be penetrated 100% Holes should be completely sealed

3.3.3.3 焊缝必须符合表3中所列的焊缝缺陷的极限值

3.3.3.3 Welded seam should conform to limit values of welded seam flaws listed in Table 3.

若图纸没有其它的要求,则下表对缺陷的极限值适用。焊缝缺陷不允许对表面保护有不好的影响。

If there are no other requirements in the drawings, the follow table shall apply to limit values of flaws. Flaws of welded seams should not have unfavorable impact on surface protection. 评价级别 D-低 C-中 B-高

Evaluation grade D-low C-medium B-high 表3 焊缝缺陷的极限值

Table 3 Limit values of flaws of welded seams 序号 1 2

缺陷名称 裂纹 孔隙率和气孔 说明 2)单个气孔的最大尺寸 不规则性的极限值 评价级别 规定值 C B 不允许 1% h≤0.3a mm 15

1)全部气孔在投影面或折射面上的最大尺寸 B 打印、拷贝即为非受控文件,请核查最新版本

- Printed Copy is Uncontrolled – Check Issue is Current -

SMTC 21549?2010

3 4 5 6 气道和条状气孔 夹杂(除铜外) 未熔合 熔深不够 1)长的不规则性1)长的不规则性 (2) B B B B C 规定熔深 实际熔深 B 不允许 h≤0. 3a mm 不允许 h≤0. 3a mm 不允许 若低于最低熔深不允许 2)短的不规则性2)短的不规则性(1)(2)(1) 7 间隙的配合 B h≤0.5+0.1 a mm 最大2 mm 8 咬边 B h≤0.5mm 9 余高太大 B h≤1+0.1b mm 最大3 mm 16

打印、拷贝即为非受控文件,请核查最新版本

- Printed Copy is Uncontrolled – Check Issue is Current -

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说综合文库汽车底盘零件焊接质量评价 - 图文(4)在线全文阅读。

汽车底盘零件焊接质量评价 - 图文(4).doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/zonghe/619141.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: