77范文网 - 专业文章范例文档资料分享平台

英文版钻井设计手册ENI- Drilling Design Manual - 图文(4)

来源:网络收集 时间:2019-04-22 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

ARPO ENI S.p.A. Agip Division IDENTIFICATION CODE STAP-P-1-M-6100 PAGE 16 OF 230 REVISION 0 ? Cuttings from normal pressured shales are small with

rounded edges and are generally flat, while cuttings from an abnormal pressure are often long and splintered with angular edges. As the differential between the pore

pressure and the drilling fluid hydrostatic head is reduced, the pressured shales will burst into the wellbore rather than having being drilled. This change in shape, along with an increase in the amount of cuttings at the surface, could be an indication that abnormal pressure has been encountered.

2.2.5.

Methods After Drilling

These are methods founded on the elaboration of the data from electrical logs such as: induction log (IES), sonic log (SL), formation density log (FDC), neutron log (NL). The most used methods for abnormal pressure detection are:

Induction Log (IES) Method:

Is used in sand and shale formations and consists in the plotting of the shale resistivity values at relative depths on a semilog graphic (depth in decimal scale and resistivity in logarithmical scale).

In formations, if they are normal compacted, the resistivity of the shales increases with depth but, in overpressure zones, it lowers with depth increase (Refer to figure .2.a).

Also it is possible to plot the values of the shale conductibility; in this case the plot will be symmetric to that described above. The method is acceptable only in shale salt water bearing formations which have sufficient and a constant level of salinity.

For the calculation of gradient, refer to the ?Overpressure Evaluation Manual?.

ARPO ENI S.p.A. Agip Division IDENTIFICATION CODE STAP-P-1-M-6100 PAGE 17 OF 230 REVISION 0 Fig.1,2-1 INDUCTION LOG

1

Resistivity (OHMM)

10

100

1500

??????? ??????? ??????????????????????????????????????????????????????? To ?????? ?????????????????????????????????????????? 2000

2500

3000

3500

4000

4500

5000

Figure .2.A - Induction Log

Shale Formation Factor This is more sophisticated than the IES method described

above. It eliminates the inconveniences due to water salinity (Fsh) Method:

variation. It consists in the plotting of the shale factors on a semilog graph (depth in decimal scale and resistivity in

logarithmical scale)at relative depths. The ?Fsh? is calculated by the following formula:

Rsh Fsh???Rw

Where: Rsht Rw

=The shale resistivity read on the log in the points where they are most cleaned

= The formation water resistivity reported in

?Schlumberger?s tables on the ?log interpretation chart?.

The value of Fsh, increases with depth in normal compaction zones and lowers in overpressure zones (Refer to figure 2.b). For the gradients calculation, the ?Overpressure Evaluation Manual?.

ARPO ENI S.p.A. Agip Division IDENTIFICATION CODE STAP-P-1-M-6100

1

1500

F shale

10

0

100

PAGE 18 OF 230 REVISION 2000

2500

Depth (m) 3000

3500

4000

4500

5000

Figure 2.B - ‘F’ Shale

Sonic Log (SL) Method: Also termed ???t shale?, is the most widely used as, from

experience, it gives the most reliability. It consists in the plotting, on a semilog graph (depth in decimal scale and transit time in logarithmical scale) of the???t values (transit time) at relative depths.

The???t value (transit time) is read on sonic log in the shale points where they are cleanest;???t value lowers with the depth increase in normal compaction zones and increases with the depth in overpressure zones (Refer to figure 2.c) For the calculation of gradient, refer to the ?Overpressure Evaluation Manual?.

ARPO

ENI S.p.A. Agip Division

IDENTIFICATION CODE

STAP-P-1-M-6100

10 0 500 1000 1500

100

0

1000

PAGE

19 OF 230

REVISION

3500 Depth (m) 2000 2500 3000

?????????

2.3.

5000 4000 4500

????????? ?????????????????? ????????? ???????????????????????????????????????????? Top ???????? ???????????????? ???????? ???????????????????????????????? Figure 2.C Sonic log

TEMPERATURE PREDICTION

The temperature at various depths to which a well is drilled must be evaluated as it has a great influence on the properties of both the reservoir fluids and materials used in drilling operations.

The higher temperatures encountered at increasing depth usually have adverse effects upon materials used in drilling wells but may be beneficial in production as it lowers the viscosity of reservoir fluids allowing freer movement of the fluids through the reservoir rock. In drilling operations the treating chemicals materials and clays used in drilling mud become ineffective or unstable at higher temperatures and cement slurry thickening and setting times accelerate (also due to increasing pressure).

Another effect of temperature is the lowering of the strength and toughness of materials used in drilling and casing operations such as drillpipe and casing.

As technology improves and wells can be drilled even deeper, these problems become more prevalent.

ARPO ENI S.p.A. Agip Division 2.3.1.

Temperature Gradients

IDENTIFICATION CODE STAP-P-1-M-6100 PAGE 20 OF 230 REVISION 0 The temperature of the rocks at a given point, formation temperature, and relationship between temperature and depth is termed the thermal gradient. Temperature gradients around the world can vary from between 1oC in 110ft (35m) to 180ft (56m).

The heat source is radiated through the rock therefore it is obvious that temperature

gradients will differ throughout the various regions where there are different rocks. Seasonal variations in surface temperatures have little effect on gradients deeper than 100ft (30m) except in permafrost regions.

It is important therefore that the local temperature gradient is determined from previous drilling reports, offset well data or any other source. In most regions, the temperature gradient is well known and is only affected when in the vicinity of salt domes. If the temperature gradient is not known in a new area, it is recommended that a gradient of 3oC/100m be assumed.

The calculation of temperature at depth if the thermal gradient is known, is simply: T = Surface Ambient Temp + Depth/Gradient (Depth per Degree Temp)

2.3.2.

Temperature Logging

During the actual drilling of a well, temperature surveys will be taken at intervals which may help to confirm the accuracy of the temperature prediction.

Temperature measurement during drilling may be by simple thermometer or possibly by running thermal logs, however, the circulation of mud or other liquids tends to smooth out the temperature profile around the well bore and mask the distinction of the individual strata. Consequently the use of temperature logs during drilling is uncommon.

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说综合文库英文版钻井设计手册ENI- Drilling Design Manual - 图文(4)在线全文阅读。

英文版钻井设计手册ENI- Drilling Design Manual - 图文(4).doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/zonghe/617064.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: