日立HITACHI钻孔机操作手册(4)

START ATC锁住

NO.282 M ADDRESS LOCK RESET M CODE锁住 NO.283 REPLACE TOOL PALLET,

TOOL NOT AVAILABLE START 请交换供给部工具盘（工具已用完） NO.284 REPLACE TOOL PALLET, SWITH ATCIVATE

START 请交换供给部工具盘（SWITCH ON）

NO.285 CHECK POD START 排出，装着POD确认 NO.286 INSERT TOOL INTO COLLET MANUALLY START 手动将工具插入COLLET中（粗径）

NO.287 REMOVE TOOL INTO COLLET MANUALLY START 手动将COLLET之工具排出（粗径）

NO.290 ATC CHUCK ALARM(LOWER) START ATC CHUCK异状（下降端） NO.291 ATC CHUCK ALARM(UPER) START ATC CHUCK异状（上升端） NO.292 CHECK ATC CHUCK NG(LONG) START 检查ATC CHUCK 钻针（长） NO.293 CHECK ATC CHUCK NG (SHORT) START 检查ATC CHUCK钻针（短） NO.294 ALL SPINDLES CANCELLED RESET 全部SPINDLE轴取消 NO.300 SPINDLE FUSE ALARM START SPINDLE FUSE警报 NO.301 SPINDLE INVERTER ALARM EMG SPINDLE变频器警报 NO.302 LOW AIR PRESSURE START 空压不足

NO.303 COLLING UNIT THERMAL ALARM EMG 主轴油冷却装置热电驿警报 NO.304 COOLING UNIT TEMPERATURE START 主轴油冷却装置油温警报 NO.305 VACLUM THARMAL ALARM EMG 集尘机热电驿警报 NO.306 ATC POINT ALARM START A TC位置警报 NO.307 BDD ALARM START 断针警报（BDD）

NO.308 EXTERNAL DEVICE ALARM START 外部装置警报

HITACHI日立(H-MARK-30R)钻孔机操作手册

NO.313 SPINDLE OIL SIGNAL RESET SPINDLE油信号警报 NO.314 ABC DEVICE ALARM

START ABC装置警报

No.315 DRYING UNIT OFF START 空气干燥机停止中 No.316 WORK CLAMP ALART RESET 基板固定CLAMP机能异常检出 No.317 PIN CLAMP ALARM RESET PIN CLAMP机能异常 No.318 WORK PRESS ALARM RESET 押板机能动作异常 No.319 SAFETY SENSOR ALARM RESET 安全SENSOR警报2 No.320 XY AXIS INTERLOCK(G64.4) EMG X，Y轴连结锁住(G64.4) No.321 Z AXIS INTERLOCK(G72.4) EMG Z轴连结锁住(G72.4) No.322 CUTTING INTERLOCK(G00.1) EMG 切削连结锁住(00.1) No.323 SPINDLE OFF EMG SPINDLE 停止中 No.324 MACHIINE LOCK EMG 机械锁定

No.325 WAITING FOR M-ANS.DGN.039 RESET M CODE等待回应 No.326 START INHIBIT EMG 启动停止 No.327 WAIT FOR WARM-UP SPINDLE EMG SPINDLE暖机中 No.328 EXECUTING ABC CYCLE EMG ABC动作中 No.329 WAITING FOR OPERATINO START 等待状态 No.330 END OF PROGRAM START 作业完了 No.331 PUSHING WORKPRESS EMG 押板机能动作中 No.337 ABC NOT READY START 外部装置ABC未就续 No.346 PACK COMMUNICATION ALARM X11-12 EMG PACK通讯异常 No.347 DEAE STOP ERROR EMG 超极限检出警报 No.350 BDD ALARM RESET 断针警报(BDD) No.351 PRESET SCHEDULE EMG 1V/1W加工异常 No.352 SELECTED ILLEGAL MODE RESET 加工模式异常 No.353 RECLINNING ALARM RESET 板架栅栏警报(ABC) No.354 TOOL ASSINGNMENT ERROR， RESET 工具分配错误，检查工具 CHECK ON TOOL PALLET PAGE 分配页 No.403 X ENCODER ALARM EMG X轴编码器警报 No.405 X OVER SERVO DLOOP EMG X轴伺服回路超出行程 No.406 X AXIS INTERLOCK EMG X轴联结警报 No.407 X VELOCTY ALARM EMG X轴速度警报 No.408 X REFERENCE POINT ALARM EMG X轴参考点警报 No.409 X SERVO ALARM EMG X轴伺服关系警报 No.413 Y ENCODER ALARM EMG Y轴编码器警报 No.415 Y OVER SERVO DLOOP EMG Y轴伺服回路超出行程 No.416 Y AXIS INTERLOCK EMG Y轴联结警报 No.417 Y VELOCTY ALARM EMG Y轴速度警报

HITACHI日立(H-MARK-30R)钻孔机操作手册

No.423 Z1 ENCODER ALARM EMG Z1轴编码器警报 No.425 Z1 OVER SERVO DLOOP EMG Z1轴伺服回路超出行程 No.426 Z1 AXIS INTERLOCK EMG Z1轴联结警报 No.427 Z1 VELOCTY POINT ALARM EMG Z1轴速度警报 No.428 Z1 REFERENCE POINT ALARM EMG Z1轴参考点警报 No.429 Z1 SERVO ALARM EMG Z1轴伺服关系警报 NO.433 Z2 ENCODER ALARM EMG Z2轴编码器警报 NO.435 Z2 OVER SERVO DLOOP EMG Z2轴伺服回路超出行程 NO.436 Z2 AXIS INTERLOCK EMG Z2轴联结警报 NO.437 Z2 VELOCTY ALARM EMG Z2轴速度警报 NO.438 Z2 REFERENCE POINT ALARM EMG

Z2轴参考点警报

Z2轴伺服关系警报

NO.439 Z2 SERVO ALARM EMG

NO.443 Z3 ENCODER ALARM EMG Z3轴编码器警报 NO.445 Z3 OVER SERVO DLOOP EMG NO.446 Z3 AXIS INTERLOCK EMG NO.447 Z3 VELOCTY ALARM EMG

Z3轴伺服回路超出行程 Z3 轴联结警报 Z3轴速度警报

NO.448 Z3 REFERENCE POINT ALARM EMG Z3轴参考点警报 NO.449 Z3 SERVO ALARM EMG NO.453 Z4 ENCODER ALARM EMG

Z3轴伺服关系警报 Z4轴编码器警报

NO.455 Z4 OVER SERVO DLOOP EMG Z4轴伺服回路超出行程 NO.456 Z4 AXIS INTERLOCK EMG Z4轴联结警报 NO.457 Z4 VELOCTY ALARM EMG Z4轴速度警报

NO.458 Z4 REFERENCE POINT ALARM EMG Z4轴参考点警报 NO.459 Z4 SERVO ALARM EMG Z4轴伺服关系警报 NO.463 Z5 ENCODER ALARM EMG Z5轴编码器警报 NO.465 Z5 OVER SERVO DLOOP EMG Z5轴伺服回路超出行程 NO.466 Z5 AXIS INTERLOCK EMG Z5轴联结警报 NO.467 Z5 VELOCTY ALARM EMG Z5轴速度警报 NO.468 Z5 REFERENCE POINT ALARM EMG Z5轴参考点警报 NO.469 Z5 SERVO ALARM EMG Z5轴伺服关系警报

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读，免费范文网，提供经典小说公务员考试日立HITACHI钻孔机操作手册(4)在线全文阅读。